Morgana DigiBook 450 Instruction Manual Download Page 57

Page: 57 / 93

Operators Guide

DigiBook 450

rel. 2.00-B

A37

Jogger Out of Position

Jogger not in position, the alarm occurs when the cutter is ex-
cluded and the jogger is not put in the zero position. Set the jog-
ger to zero position.

A38

Mill Door not Closed

Protection of the cutter is not closed. Verify that the cover closes
and if necessary clean the guide.

A39

Mill Group Out of Position

Milling station is not in place, make sure that the lever is or ON
or OFF position.

A40

Group Up/Down Press not in position

Height adjustment of the press is not in right position. Press
START

A43

Thermal Switch QM13.01-02-03

Thermal overload of one of the following motors, milling, plane
ascent covers, discharge conveyor. It is necessary to enable them

by hand inside the electrical panel.

Before doing

this, verify everything and disconnect the power from the
machine.

A44

Wrong Reading Glue Photocell

Photocell has read two pulses, do not insert two books or clean
the clamp.

A45

TUTORIAL NOT COMPLETED

Complete the tutorial and continue.

A46

No Air Pressure

Air pressure fault to the machine. Verify that the manometer
at the entry is at 6 bar (87psi) or that the compressor is suit-
able.

A47

PLC Battery Low

A48

End of Production

End of production appears when the copy counter has reached the
predetermined number of books.

A49

Lack of cover on nipping station

A61

Creasing Setpoint Out of Range

Check that the setpoint plus additional corrections is not less than
0.79in or more than 2in

A62

Books Stacker Full

Remove books from stacker (OTIONAL)

A64

Error Double Cover

Remove the covers in excess from the press. (OPTIONAL)

A65

Error on Cover Pick-up

Error in picking up covers. It appears at third time. Verify vacu-
um pressure, split blades, power and front blows position.

A66

Cover Jam

Remove the cover from the transit area on creasers.

A67

Cover Front Setpoint too Small

Check the difference between the length of the cover and position
of the rear guide is not less than 4.72in or more than 12.79in

A70

Please Remove Covers Pack

Necessary to allow the movement of the cover guide on the cover
feeder plane.

A71

Photocell Discharge Book Obstructed

Verify the guide for releasing the book

A78

Timeout Press Opening/Closing

Up / down movement of the nipping station too slow or not made.
Increase the pressing pressure.

A79

Timeout Contrast Opening/Closing

Movement of the plane spine book too slow or motion not com-
pleted. Verify there are not obstructions or glue.

A80

Timeout Pick Place Rotation

Rotation of the delivery arm not completed Verify the release
guide.

MyBinding.com

5500 NE Moore Court

Hillsboro, OR 97124

Toll Free: 1-800-944-4573

Local: 503-640-5920

Summary of Contents for DigiBook 450






























































































Search results

Summary of Contents for DigiBook 450

Reviews:

Related manuals for DigiBook 450

Brands by name

Popular brands

Morgana DigiBook 450, Instruction Manual

Search results

Summary of Contents for DigiBook 450

Reviews:

Related manuals for DigiBook 450

Brands by name

Popular brands