Mitsubishi Electric Melsec WS Series User Manual Download Page 102

Page: 102 / 142

MELSEC-WS

Procedures before operation

3) Configuring TCP/IP

Configure the communication mode (auto update mode) in the

TCP/IP

configuration

dialog.

Select

Enable auto update and COS

and

Connect to

for socket 1.

(In the sample program, the WS0-GETH is configured as master.)

Option

Configuration value

(Listen to)

Configuration value

(Connect to)

Enabled Checked
Listen to

Selected

Deselected

Port

9100

(238C

) (default)

Connect to

Deselected

Selected

address

192.168.250.251

Port -

9100

(238C

)

Enable COS update/Enable
auto update and COS

Enable auto update and COS

Update rate (ms)

5000 (default)

Update Dataset 1

Checked

Update Dataset 2

Checked

Update Dataset 3

Checked

Update Dataset 4

Unchecked

To switch the communication mode to the polling mode, activate the

Enable COS

update

radio button.

4) Editing data sets

Refer to Section 8.2.2 (1).

Figure 57:
TCP/IP configuration
dialog

Table 33:
TCP/IP configuration
parameters

Summary of Contents for Melsec WS Series















































































































































Search results

Summary of Contents for Melsec WS Series

Reviews:

Related manuals for Melsec WS Series

Brands by name

Popular brands

Mitsubishi Electric Melsec WS Series, User Manual

Search results

Summary of Contents for Melsec WS Series

Reviews:

Related manuals for Melsec WS Series

Brands by name

Popular brands