manualshive.com logo in svg

Mitsubishi Electric Melsec WS Series, User Manual

Share
Download
Mitsubishi Electric Melsec WS Series User Manual Download Page 57

Data sets

  

MELSEC-WS 

54 

4.4.3 

Network Module Data area 

This area contains the routing table. It shows the current content of the Ethernet 
interface module’s input data modules. Bytes and bits highlighted blue will hold “live” 
data from the system since the hardware configuration does support the source. 
Bytes highlighted grey actually do not have data associated with them since the 
hardware configuration does not support the sources. 
 

How to delete a data byte from the routing table: 

  Drag and drop the byte you want to delete to the trashcan icon in the bottom left 

corner of the 

Network Module

 

Data

 area. 

Or:

 

  Select the byte you want to delete by clicking it with the left mouse button. Then, 

click on the 

Delete

 

routing

 button in the toolbar. 

Or:

 

  Call up the context menu by clicking the respective byte with the right mouse 

button. In the context menu, select the 

Delete

 

routing

 command. 

 

How to move a data byte to another place in the routing table: 

  Drag and drop the byte you want to move to the desired position. If the desired 

position is not free, you will have to clear it first by deleting or moving the byte 
currently assigned to it. 

 

4.4.4 

Tag names area 

This area shows the tag names associated with each bit of the byte currently 
selected in the 

Available

 

data

 or the 

Network Module

 

Data

 area. You can enter 

these tag names in the tag name editor. 

In the 

Tag

 

names

 area of the 

CPU to Ethernet

 configuration dialog, you can only 

edit tag names for unassigned data sets by activating the 

Use direct editing

 

checkbox (with CPU module firmware version V2.00.0 or higher). 

 

 

 

Summary of Contents for Melsec WS Series















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands