manualshive.com logo in svg

Mitsubishi Electric Melsec WS Series, User Manual

Share
Download
Mitsubishi Electric Melsec WS Series User Manual Download Page 14

MELSEC-WS 

About this document

 

11 

1.4  Depth of information 

This manual contains information on the Ethernet interface module in the following 
subjects: 

 

mounting 

 

implementation into a network 

 

configuration via Setting and Monitoring Tool 

 

data transfer to and from the network 

 

status information, planning and related mapping 

 

part numbers 

 

Warning! 

Pay attention to the safety notes and safety measures on the Ethernet interface 
module! 

 
For the acquisition of Setting and Monitoring Tool, please contact your local 
Mitsubishi representative. 

1.5 Scope 

This manual applies to the WS0-GETH Ethernet interface module. 

This document is the original manual. 

1.6 Abbreviations used 

Enhanced Function Interface 

1.7 Symbols used 

Notes provide special information on the device. 

LED symbols describe the state of a diagnostics LED. Examples: 

Red

 

The red LED is illuminated constantly. 

Red

 

The red LED is flashing. 

Green

  The green LED is off. 

Instructions for taking action are shown by an arrow. Read carefully and follow the 
instructions for action. 

 

ATTENTION! 

An “ATTENTION” indicates an actual or potential risk or health hazard. They are 
designed to help you to prevent accidents. 
Read carefully and follow the attention notices! 

 
 

 

ATTENTION 

Note 

EFI 

Note 

Red, Red, 

Green 

 Action 

 

ATTENTION 

Summary of Contents for Melsec WS Series















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands