Mitsubishi Electric Melsec WS Series User Manual Download Page 70

Page: 70 / 142

MELSEC-WS

Procedures before operation

(b) Communications with the Built-in Ethernet port QCPU

The following is a procedure to establish communications between the WS0-
GETH and the Built-in Ethernet port QCPU.

Procedure before operation

Connect the WS0-GETH

to the MELSEC-WS

CPU module.

Connect an Ethernet cable.

Write the configuration

data to the module

with Setting and

Monitoring Tool.

End

Connect an Ethernet cable.

Check operations.

Built-in Ethernet port QCPU

WS0-GETH

Create a ladder program.

Configure PLC parameters

with GX Developer.

Configure configuration

data with Setting and

Monitoring Tool.

Figure 30:
Procedure before
operation
(communications with
the Built-in Ethernet
port QCPU)

Summary of Contents for Melsec WS Series















































































































































Search results

Summary of Contents for Melsec WS Series

Reviews:

Related manuals for Melsec WS Series

Brands by name

Popular brands

Mitsubishi Electric Melsec WS Series, User Manual

Search results

Summary of Contents for Melsec WS Series

Reviews:

Related manuals for Melsec WS Series

Brands by name

Popular brands