manualshive.com logo in svg

Mitsubishi Electric Melsec WS Series, User Manual

Share
Download
Mitsubishi Electric Melsec WS Series User Manual Download Page 18

MELSEC-WS 

Ethernet interface module

 

15 

This chapter describes the Ethernet interface module (WS0-GETH). 

 

3.1 Overview  

The Ethernet interface module is connected to Setting and Monitoring Tool, a 
MELSEC programmable controller, and PC via TCP/IP. The module can: 

 

Exchange configuration data and programs of a MELSEC-WS safety controller 
by connecting to Setting and Monitoring Tool via TCP/IP. 

 

Exchange non-safety related data by connecting to an external application (e.g. 
MELSEC programmable controller, PC) via TCP/IP. 

 

3.1.1 

Interfaces and operation 

The Ethernet interface module is equipped with an integrated three-port switch for 
connection with the Ethernet network. Two RJ45 sockets are available for the 
connection. The switch functionality allows the Ethernet interface module to be used 
for connection to another Ethernet component (e.g. connection to a notebook) 
without having to interrupt the Ethernet connection to the network. (One IP address 
can be configured.) 

 

 
 

 

3.  Ethernet interface module 

Figure 1:  
Interfaces and display 
elements of the WS0-
GETH 

Summary of Contents for Melsec WS Series















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands