Mitsubishi Electric Melsec WS Series User Manual Download Page 69

Page: 69 / 142

Procedures before operation

MELSEC-WS

(1) Procedures before operation

(a) Communications with the QJ71E71-100

The following is a procedure to establish communications between the WS0-
GETH and the QJ71E71-100.

Procedure before operation

Connect the WS0-GETH

to the MELSEC-WS

CPU module.

Connect an Ethernet cable.

Configure configuration

data with Setting and

Monitoring Tool.

Write the configuration

data to the module

with Setting and

Monitoring Tool.

End

Mount the QJ71E71-100

on the base unit.

Configure network

parameters (for Ethernet)

with GX Developer.

Connect an Ethernet cable.

Create a ladder program.

Check operations.

QJ71E71-100

*1 For details, refer to the Q Corresponding Ethernet Interface Module User's Manual (Basic).

WS0-GETH

Execute a PING test

to check for existence

of the WS0-GETH.

8. Procedures before operation

Figure 29:
Procedure before
operation
(communications with
the QJ71E71-100)

Summary of Contents for Melsec WS Series















































































































































Search results

Summary of Contents for Melsec WS Series

Reviews:

Related manuals for Melsec WS Series

Brands by name

Popular brands

Mitsubishi Electric Melsec WS Series, User Manual

Search results

Summary of Contents for Melsec WS Series

Reviews:

Related manuals for Melsec WS Series

Brands by name

Popular brands