manualshive.com logo in svg

Mitsubishi Electric Melsec WS Series, User Manual

Share
Download
Mitsubishi Electric Melsec WS Series User Manual Download Page 64

MELSEC-WS

 Technical 

specifications

 

61 

 

6.1 Technical specifications of Ethernet interface 

module 

Interface 

Fieldbus 

Ethernet TCP/IP 

Integrated switch 

3-port layer-2 managed switch with Auto-MDI-X for 
automatic detection of crossed Ethernet cable 

Connection technique 

RJ45 socket 

Transfer rate 

10 Mbps (10Base-T) or 100 Mbps (100Base-TX), 
autosensing 

Update rate  
(heartbeat rate) 

Configurable from 40 to 65535 ms 

Change of state (COS) 
update rate 

10 ms 

Addressing factory 
setting 

IP address: 192.168.250.250 
Subnet mask: 255.255.0.0 
Default gateway: 0.0.0.0 

MAC address 

Printed on type label, example: 00:06:77:02:00:A7 

6.2  Technical specifications, supply circuit 

 

Item 

Specifications 

Supply voltage 

24 V DC (16.8 to 30 V DC) 

Power consumption 

Max. 2.4 W 

6.3 General technical specifications 

Terminals 

Fieldbus 

Ethernet (TCP/IP) 

 

10-pin connector for internal safety bus (plug) 

 

Climatic conditions 

Ambient operating temperature T

A

 

-25 °C to +55 °C 

Storage temperature 

-25 °C to +70 °C 

Relative humidity 

10 % to 95 %, non-condensing 

Climatic conditions 

In accordance with EN61131-2 

 
 

 

6. Technical specifications 

Table 20:  
Technical specifications 
of Ethernet interface 
module 

Table 21:  
Technical 
specifications, supply 
circuit 

Table 22:  
General technical 
specifications 

Summary of Contents for Melsec WS Series















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands