Mitsubishi Electric Melsec WS Series User Manual Download Page 63 | Manualshive

Page: 63 / 142

background image

Troubleshooting

MELSEC-WS

60

Error

Cause

Possible remedy

WS0-GETH functioned
correctly after configuration, but
suddenly no longer supplies
data.
LED PWR



Green

LED LINK/ACT



/

Green

LED MS

Red/Green

WS0-GETH is operated in slave
mode, the IP address is assigned
from a DHCP server. After the WS0-
GETH or the DHCP server has been
restarted, a different IP address that
is unknown to the programmable
controller has been assigned to the
WS0-GETH.

Either assign a fixed IP address to the WS0-
GETH, or reserve a fixed IP address for the
WS0-GETH in the DHCP server (manual
assignment by means of the MAC address of
the WS0-GETH).

WS0-GETH/safety controller is
in Critical fault mode.
LED PWR



Green

LED LINK/ACT

Green

LED MS



Red

WS0-GETH is not plugged properly
into the other MELSEC-WS module.
Module connection plug is soiled or
damaged.
Other MELSEC-WS module has
internal critical error.
Ethernet communication with the
WS0-GETH is under excessive load.

Plug the WS0-GETH in correctly.
Clean the connecting socket/plug.
Repower the safety controller.
Check the error MELSEC-WS module and
remove the error cause.
Check the Ethernet line status. If a load is
excessively placed to the line, reduce the load
using a device such as a router.

WS0-GETH is in Critical fault
mode.
LED PWR



Green

LED LINK/ACT



/

Green

LED MS

Red (2 Hz)

WS0-GETH internal device error

Switch off the power supply of the safety
controller and switch it on again.
Check if the WS0-GETH is mounted in correct
position.
Check the diagnostics messages with the
Setting and Monitoring Tool.
If the error remains, replace the Ethernet
interface module.

«
...
61
62
63
64
65
...
»

Summary of Contents for Melsec WS Series















































































































































Reviews:

No comments

Related manuals for Melsec WS Series

Brand: Watts Pages: 2

Brand: Lawler Pages: 4

Brand: Hama Pages: 46

Brand: Galcon Pages: 35

Brand: ZKTeco Pages: 2

Brand: FASAR ELETTRONICA Pages: 2

Brand: Faro Barcelona Pages: 8

Brand: Faro Pages: 3

Brand: YASKAWA Pages: 456

Brand: Häfele Pages: 2

Brand: Häfele Pages: 24

ServeRAID-MR10is

Brand: IBM Pages: 94

ServeRAID-4 Ultra160 Series

Brand: IBM Pages: 20

8271 Nways Ethernet LAN Switch

Brand: IBM Pages: 6

Brand: IBM Pages: 86

Brand: IBM Pages: 205

Brand: IBM Pages: 28

Brand: M-system Pages: 103

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands