manualshive.com logo in svg

Mitsubishi Electric Melsec WS Series, User Manual

Share
Download
Mitsubishi Electric Melsec WS Series User Manual Download Page 33

Ethernet interface module

  

MELSEC-WS 

30 

 

 

 Click 

OK

. All communication to the MELSEC-WS safety controller will now 

happen via TCP/IP. In order to use the entry point via the serial interface again, 
you will have to re-activate it. 

The port number for the TCP/IP configuration interface is pre-set to port 9000 and 
can not be changed. 

 

Step 3: Connect via TCP/IP 

  Click on the 

Connect

 button to go online. 

While Setting and Monitoring Tool is connected via TCP/IP, do not transfer the 
parameters in which the IP address of the connected Ethernet interface module has 
been changed. Doing so will result in disconnection of communication. In that case, 
click on the 

Disconnect

 button to go offline, make the correct configuration in the 

Connection settings

 dialog, and then retry the connection. 

 
 

 

Figure 15:  
Connection settings 
dialog with new TCP/IP 
profile activated 

Note 

Note 

Summary of Contents for Melsec WS Series















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands