Mitsubishi Electric Melsec WS Series User Manual Download Page 27

Page: 27 / 142

Ethernet interface module

MELSEC-WS

You can assign an IP address from

Network settings

in the

Connection settings

dialog.



Click on the

Network settings

button. The

Network scan

dialog is opened.



Click on the

Scan

button. Your network is scanned for connected network

modules and the network modules found are displayed in the list.



Click on the Ethernet interface module you want to edit.



Enter the new settings in the

Edit IP address

area.



Click on the

Set device config

button to transfer the new settings to the

Ethernet interface module.



If multiple Ethernet interface modules are connected to the PC, network scanning
may fail. In that case, disable the unused modules.



The

Open web browser

button is unavailable for Ethernet interface modules.

3.4.3

Configuration of the Ethernet interface module

For the configuration of the Ethernet interface module, please refer to Section 3.5.
For the configuration of the input data set 1 (data transfer from and to the network),
please refer to Section 4.4 and Section 4.5.

Figure 10:
Found network modules
in the Network scan
dialog

Note

Summary of Contents for Melsec WS Series















































































































































Search results

Summary of Contents for Melsec WS Series

Reviews:

Related manuals for Melsec WS Series

Brands by name

Popular brands

Mitsubishi Electric Melsec WS Series, User Manual

Search results

Summary of Contents for Melsec WS Series

Reviews:

Related manuals for Melsec WS Series

Brands by name

Popular brands