manualshive.com logo in svg

Mitsubishi Electric Melsec WS Series, User Manual

Share
Download
Mitsubishi Electric Melsec WS Series User Manual Download Page 39

Ethernet interface module

  

MELSEC-WS 

36 

 

 

 Check the 

Listen to

 checkbox. 

 Enter the 

Port

 number on which the application will connect. 

  Select the update mode: 

Enable COS update

 or 

Enable auto update and 

COS

. 

  If you have selected 

Enable auto update and COS

, select the 

Update rate

 in 

ms. (Configurable range: 40 to 65535) 

  Select which data sets shall be updated: Check the 

Update Dataset n

 

checkbox. 

 

Ethernet interface module writes to Address/Port (Auto update) mode 

The Ethernet interface module can be configured to automatically update the data 
set information (i.e. the application does not need to send any request messages as 
it would do in polling mode) once the connection to the application has been made. 

The configuration settings are available via the Setting and Monitoring Tool or via the 
TCP/IP interface itself. Using one interface does not disable the other: The auto 
update mode could be enabled via Setting and Monitoring Tool and disabled via 
TCP/IP command, for example. 
 

Configuration via TCP/IP interface 

This command message is sent by an application to the Ethernet interface module 
to configure the auto update mode. This message can be used to either disable or 
enable the auto update mode directly through the TCP/IP interface. 

 

 

 

Figure 17: 
TCP/IP configuration for 
polling mode 

Summary of Contents for Melsec WS Series















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands