manualshive.com logo in svg

Mitsubishi Electric Melsec WS Series, User Manual

Share
Download
Mitsubishi Electric Melsec WS Series User Manual Download Page 122

MELSEC-WS

  

Procedures before operation

 

119 

For details of data reception processing in a program for receiving input data sets 

in auto update mode, refer to Section 8.2.4 (2). 
Replace the BUFSND and BUFRCV instructions with the SOCSND and 
SOCRCV instructions. 

 

Since the Built-in Ethernet port QCPU treats application data in Little Endian 

format, the byte-order needs to be swapped. Note that the byte order of the input 
data set 1 and output data set 1 does not need to be changed because these 
data are one byte long. 

<Data need to be swapped> 

 

Command and parameters (word data (16 bits)) 

 

Input data sets 2 and 3 (double-word data (32 bits)) 

 
(3) Monitoring data with a programming tool 

The read input data sets can be monitored using the device monitor function of a 

programming tool. For the execution results of the program for auto update 
mode, refer to Section 8.2.2 (3). 

 

 

Summary of Contents for Melsec WS Series















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands