Metso NELES NDX 511 Series Installation Maintenance And Operating Instructions Download Page 23

Page: 23 / 88

GENER

INFO

SPECS

MOUNTING

T UP

OPER

ATION

AINTENANCE

DIMENSIONS

ORDER

LOGISTICS

NDX VALVE CONTROLLER

7.3

Installation to any linear actuator

NDX can be easily installed to any linear actuator when the

following installation rules are followed. In order to guar

antee the best possible position measurement accuracy,

NDX and position feedback magnet must be positioned

according to the following guidelines.

Tol/ 3 [mm]

Magnet center

Magnet center travel limit

(fixing bolt line)

Magnet center travel limit

(fixing bolt line)

Fig. 22

When installing the device to any other actuator model

make sure that the following tolerances are followed with

magnet mounting.

1. Magnet shall be centered / 3 mm tolerance

as shown in the picture.

2. Magnet center shall never exceed the magnet center

travel limits shown in the picture.

NOTE

Use only Metso original magnets.

Bracket and fixing bolt material should have

low magnetic permeability (e.g. AISI316 or

aluminium).

NOTE

Always ensure that the magnet center stays

within magnet center travel limits on the

complete operation range of the valve.

NOTE

Shorter actuator stroke allows more freedom

for alignment of the magnet and NDX in

actuator stroke direction. Magnet position does

not affect the measurement accuracy as long

as the magnet center stays within the magnet

center travel limits for whole travel range.

LINEAR MOUNTING

MOUNTING

Summary of Contents for NELES NDX 511 Series

























































































Search results

Summary of Contents for NELES NDX 511 Series

Reviews:

Related manuals for NELES NDX 511 Series

Brands by name

Popular brands

Metso NELES NDX 511 Series, Installation Maintenance And Operating Instructions

Search results

Summary of Contents for NELES NDX 511 Series

Reviews:

Related manuals for NELES NDX 511 Series

Brands by name

Popular brands