Metso NELES NDX 511 Series Installation Maintenance And Operating Instructions Download Page 6

Page: 6 / 88

NDX VALVE CONTROLLER

NOTE

Avoid grounding a welding machine in close

proximity to a valve controller. Damage to

the equipment may result.

CAUTION

Do not exceed the permitted values!

Exceeding the permitted values marked on

the valve controller maycause damage to the

controller and to equipment attached to the

controller and could lead to uncontrolled pres

sure release in the worst case. Damage to the

equipment and personal injury may result.

CAUTION

Do not remove or dismantle a pressurized

controller!

Removing or dismantling pressurized pneu

matic components of a valve controller leads to

uncontrolled pressure release. Always shut off

the supply air and release the pressure from the

pipelines and equipment before removing or

dismantling the controller. Other wise personal

injury and damage to equipment may result.

WARNING

During automatic or manual calibration the

valve operates between open and closed po

sitions. Make sure that the operation does not

endanger people or processes!

WARNING

Do not operate the device with cover removed!

Environmental influence (water, dust etc.)

Ex NOTE

Follow the standards EN/IEC 6007914 when

installing the equipment and EN/IEC 6007925

when connecting Ex i interfaces.

Ex Note

For ordinary locations and Class I Div 2 instal

lations of NDX_ _ _2 have to be supplied by a

Class 2 or Limited Energy Source in accordance

with CSA 61010112/UL 610101.

Ex WARNING

Electrostatic charge hazard!

The cover is nonconductive. Clean with

a damp cloth only! Spark hazard!

Protect the aluminum housing from impacts

and friction!

Ex WARNING

For use in the presence of combustible dust.

· Ignition protection relies on the enclosure.

Protect the cover of the valve controller from

impacts.

· When temperature is higher than 70 °C /

158 °F the temperature rating of the cable

shall be higher than the ambient temperature.

· Device shall not be subjected to a prolific

charge generating mechanism.

· Accumulation of dust shall be avoided!

Intrinsic Safety (Ex i) WARNING

· Ensure that the complete installation and

wiring is intrinsically safe before operating

the device!

· The equipment must be connected via a

certified Zener barrier placed outside the

hazardous area.

· Temperature rating of selected connection

cable shall be greater than 83 °C.

Ex n WARNING

At an ambient temperature ≥ +70 °C / 158 °F,

the temperature rating of selected connection

cable shall be in accordance with the maximum

ambient temperature range. Selected cable

gland shall not invalidate the type of protection.

Ex d WARNING (NDX Ex d version)

Do not open the device when energized!

Explosion protection is lost.

Ex d WARNING (NDX Ex d version)

After de-energizing, delay one minute

before opening!

SAFETY PRECAUTIONS

Summary of Contents for NELES NDX 511 Series

























































































Search results

Summary of Contents for NELES NDX 511 Series

Reviews:

Related manuals for NELES NDX 511 Series

Brands by name

Popular brands

Metso NELES NDX 511 Series, Installation Maintenance And Operating Instructions

Search results

Summary of Contents for NELES NDX 511 Series

Reviews:

Related manuals for NELES NDX 511 Series

Brands by name

Popular brands