Metso NELES NDX 511 Series Installation Maintenance And Operating Instructions Download Page 50

Page: 50 / 88

NDX VALVE CONTROLLER

12.8.5

Manual control

Position control

During this mode the valve position may be controlled

manually by using the arrow keys.

The manual control starts from the current position of the

valve after the manual mode is activated.

Valve position may jump when going back to auto mode

and device starts to follow setpoint.

PWM control

Control directly PWM signal to the prestage.

By pass position measurement

Can be used for identifying if problem is in positioner or if

the valve/actuator is stuck

Valve position may jump when going back to auto mode

and device starts to follow setpoint

12.8.6

User Guide

Here you find QR code for our product web pages and

support material.

Scan QR code with QR scanner on your mobile phone or tablet.

12.8.7

About

Here you find device version information.

12 LOCAL USER INTERFACE (LUI)

Summary of Contents for NELES NDX 511 Series

























































































Search results

Summary of Contents for NELES NDX 511 Series

Reviews:

Related manuals for NELES NDX 511 Series

Brands by name

Popular brands

Metso NELES NDX 511 Series, Installation Maintenance And Operating Instructions

Search results

Summary of Contents for NELES NDX 511 Series

Reviews:

Related manuals for NELES NDX 511 Series

Brands by name

Popular brands