Metso NELES NDX 511 Series Installation Maintenance And Operating Instructions Download Page 76

Page: 76 / 88

NDX VALVE CONTROLLER

NOTE

It is recommended to replace both the pre

stage and the relay valve at the same time.

•

Disconnect power from the device.

•

Shut off supply pressure and make sure that the

actuator pressure is released.

•

Remove the device from the actuator mounting

bracket if there is limited working space in front

of the prestage cover (Disconnect the supply and

actuator piping if the device has to be removed).

•

Loosen the relay valve cover screws.

•

Remove the relay valve. It is recommended to use two

screwdrivers as levers to crank out the relay valve.

Fig. 84 NDX_512_

14.3.6

Installation of relay valve

NOTE

Make sure there is no debris in the small shaft

hole, eg. from the oring of the removed relay

valve. (see picture)

Installation

NOTE: make sure there is no debris in the small shaft hole, eg. from the o-ring of the removed relay

valve. (see picture)

WARNING: Do not use any tools to install the relay valve. It can be pushed on its place just by using

hands.

Fig. 85

WARNING

Do not use any tools to install the relay valve. It

can be pushed in place by hand.

•

Align the small and large shaft in corresponding

holes. Press the relay valve into the holes with a light

continuous force. Do not use excessive force as this

may indicate the relay valve is misaligned or the

orings are not lubed.

•

Reinstall the relay valve cover. Make sure the rubber

seal is still in place on the cover and undamaged.

•

Tighten the prestage cover screws.

•

Turn on the supply pressure.

•

Reconnect electricity to the device.

•

When pneumatic components are replaced, device

requires calibration.

Fig. 86 NDX_512_

Fig. 87

14 MAINTENANCE

Summary of Contents for NELES NDX 511 Series

























































































Search results

Summary of Contents for NELES NDX 511 Series

Reviews:

Related manuals for NELES NDX 511 Series

Brands by name

Popular brands

Metso NELES NDX 511 Series, Installation Maintenance And Operating Instructions

Search results

Summary of Contents for NELES NDX 511 Series

Reviews:

Related manuals for NELES NDX 511 Series

Brands by name

Popular brands