Metso NELES NDX 511 Series Installation Maintenance And Operating Instructions Download Page 55

Page: 55 / 88

GENER

INFO

SPECS

MOUNTING

T UP

OPER

ATION

AINTENANCE

DIMENSIONS

ORDER

LOGISTICS

NDX VALVE CONTROLLER

13.5.2.3 Commissioning

DTM has a guided startup to help you with commissioning

of the device.

Fig. 57

Step 1

. Assembly Parameters

Set assembly parameters and click Next to confirm.

Fig. 58

Step 2.

Click Next to start Calibration.

Fig. 59

Step 3.

Click Finish to complete.

13.5.2.4 Status Configuration

Available statuses can be either disabled or classified to a

certain NAMUR class in Status Configuration view. Status

limits and current value is shown in the same view when

applicable.

Fig. 60

Following table lists all statuses and related events in the

event log that are available from the device. Description,

proposed actions and default NAMUR classification are

also described in the table.

Status configuration view is also available in offline mode.

To send offline parameterization to the device, open the

DTM GUI in online mode and send modifications by clicking

Apply button.

13 DEVICE TYPE MANAGER (DTM)

OPER

ATION

Summary of Contents for NELES NDX 511 Series

























































































Search results

Summary of Contents for NELES NDX 511 Series

Reviews:

Related manuals for NELES NDX 511 Series

Brands by name

Popular brands

Metso NELES NDX 511 Series, Installation Maintenance And Operating Instructions

Search results

Summary of Contents for NELES NDX 511 Series

Reviews:

Related manuals for NELES NDX 511 Series

Brands by name

Popular brands