Metso NELES NDX 511 Series Installation Maintenance And Operating Instructions Download Page 25

Page: 25 / 88

GENER

INFO

SPECS

MOUNTING

T UP

OPER

ATION

AINTENANCE

DIMENSIONS

ORDER

LOGISTICS

NDX VALVE CONTROLLER

Rotary mounting is designed according to VDI/VDE 3845

interface.

NOTE

The enclosure of NDX meets the IP66 pro

tection class according to EN 60529. Cable

entry needs to be plugged according to IP66

and it is not allowed to mount NDX in a po

sition where the cable entry is pointing up

wards. Based on good mounting practice, the

recommended mounting position is electrical

connections placed downwards. This recom

mendation is shown in our mounting position

coding for control valves.

If these requirements are not fulfilled, and the

cable gland is leaking and the leakage is dam

aging NDX, our warranty is not valid.

8.1

Installation to Neles B-series actuators -

MAGNET MOUNTING

•

Mounting set includes mechanical position

indicator. It can be used if there is no position

indicator in the actuator.

•

Place position indicator plate to the correct position

so that it correspond to the valve position.

•

Lock position indicator plate with screw driver so

that it can’t turn by bending locking tabs.

•

Mount magnet to the actuator

There shall be use thread locking in magnet assembly to

prevent magnet loosening under heavy vibration. Thread

locking should be low or medium strength, e.g. Loctite 243.

24 mm

Fig. 26

Magnet will be tightened as tight as 4 Nm. From the oper

ation point of view magnet can be in any position so there

is no adjustment needed.

8.2

Installation to Neles B-series actuators -

BRACKET MOUNTING

For Neles BJ actuators there are few different mount

ing brackets, depending on actuator size. This example

shows NDX mounting to Neles BJ6 actuator. For other sizes

bracket types vary a little, but main steps are the same.

When mounting NDX to the Neles actuators, there is no

mechanical adjustment needed.

•

Mount bracket to the NDX

•

Mount bracket to the actuator

5 mm

8 mm

Fig. 27

ROTARY MOUNTING

MOUNTING

Summary of Contents for NELES NDX 511 Series

























































































Search results

Summary of Contents for NELES NDX 511 Series

Reviews:

Related manuals for NELES NDX 511 Series

Brands by name

Popular brands

Metso NELES NDX 511 Series, Installation Maintenance And Operating Instructions

Search results

Summary of Contents for NELES NDX 511 Series

Reviews:

Related manuals for NELES NDX 511 Series

Brands by name

Popular brands