Metso NELES NDX 511 Series Installation Maintenance And Operating Instructions Download Page 54

Page: 54 / 88

NDX VALVE CONTROLLER

13.5.2

Parameterize Online

This window gives tools for quickly checking the state of

the device, perform guided commissioning process and

configure the behavior of the device.

13.5.2.1 Performance

Fig. 55

Device Status is determined based on the most acute active

status that exists in the device. Device status is classified

according to NAMUR recommendation NE 107. There can

be multiple active statuses in the device at the same time.

Status icons in the DTM are as follows:

ACTIVE EVENTS

Device Status is determined based on the most acute active event that exists in the

device. Device status is classified according to NAMUR recommendation NE 107. There

can be multiple active events in the device at the same time.

NAMUR mode status icons are as follows:

Info

Maintenance required

Off specification

Function check

Device failure

Followings active events are available from the device.

Active event

Description

Emergency Control Active

Missing Magnet

PT Not Connected

Spring Malfunction Detected

Manual control (local override)

Internal Problem

This bit will be activated only if no other bit can

communicate a device malfunction

Step test running

Valve signature test running

Valve dead band test running

Partial Stroke test test running

Calibration Recommended

Calibration Running

Supply Pressure Sensor Failure

Actuator Pressure Sensor Failure

Reduced control performance

Temperature Sensor Failure Detected

Normal

Info

Maintenance required

Off specification

Function check

Device failure

Single statuses can be enabled/disabled and classified to

certain NAMUR class in DTM’s Status Configuration view.

Related events in the event log are listed in the same chapter.

13.5.2.2 Device Information

Fig. 56

Device information view contains information on valve

controller, actuator and valve. If NDX is delivered on top of

the valve package the valve and actuator data is prefilled.

Parameter name

Description

Default value

Expanded Device Type

Code

Read expanded device

type code.

HART Technology Version Read HART technology

version of the device (6

or 7).

NDX Device Revision

Read NDX device revision.

Firmware Revision

Read firmware revision

of the device.

Firmware Build Revision Read firmware build

revision of the device.

Positioner Serial

Number

Read positioner serial

number of the device.

Positioner

Serial Number

Positioner Type Code

Read positioner type

code of the device.

Positioner

Type Code

Valve Serial Number

Write the valve serial

number here.

Valve Serial

Number

Valve Type Code

Write the valve type

code here.

Valve Type

Code

Actuator Serial Number Write the actuator serial

number here.

Actuator

Serial Number

Actuator Type Code

Write the actuator type

code here.

Actuator Type

Code

DTM Version

Read DTM version

number.

Device Type ID (HART)

Read HART device type

ID number.

13 DEVICE TYPE MANAGER (DTM)

Summary of Contents for NELES NDX 511 Series

























































































Search results

Summary of Contents for NELES NDX 511 Series

Reviews:

Related manuals for NELES NDX 511 Series

Brands by name

Popular brands

Metso NELES NDX 511 Series, Installation Maintenance And Operating Instructions

Search results

Summary of Contents for NELES NDX 511 Series

Reviews:

Related manuals for NELES NDX 511 Series

Brands by name

Popular brands