Metso NELES NDX 511 Series Installation Maintenance And Operating Instructions Download Page 57

Page: 57 / 88

GENER

INFO

SPECS

MOUNTING

T UP

OPER

ATION

AINTENANCE

DIMENSIONS

ORDER

LOGISTICS

NDX VALVE CONTROLLER

Status

Related events in the event log

Status description

Proposed actions

Default NAMUR

classification

Partial Stroke Test

Running

Partial Stroke test started

Partial Stroke test completed

Partial Stroke test failed

Partial Stroke test cancelled

Device functional test

is running.

Check the test result from DTM/EDD Event

Log.

Function

Check

Calibration Running

Automatic calibration started

Manual calibration started

1point calibration started

Calibration successful

Calibration failed

Calibration failed in tuning

Calibration failed due to

incorrect magnet installation.

Calibration cancelled

Calibration start failed

Device calibration is

running.

Check the result from DTM/EDD Event Log.

Function

Check

Positioner Diagnostics

Status

Related events in the event log

Status description

Proposed actions

Default NAMUR

classification

Total Relay Valve

Travel Limit Exceeded

Total relay valve travel limit

exceeded

Total relay valve travel limit

recovered

Userdefined limit

exceeded.

Review the device performance. If perfor

mance is adequate, increase value of Total

Relay Valve Travel Limit in DTM/EDD Status

Configuration view

Disabled

Total Operation

Time Limit Exceeded

Total operation time limit

exceeded

Total operation time limit

recovered

Userdefined limit

exceeded.

Review the device performance. If perfor

mance is adequate, increase value of Total

Operation Time Limit in DTM/EDD Status

Configuration view.

Maintenance

Required

Supply Pressure

Sensor Failure

Supply Pressure Sensor Failure

Detected

Supply pressure sensor

recovered

Supply pressure mea

surement is faulty.

Control performance

is reduced.

Change the printed circuit board module to

a new one during next maintenance activ

ity. Follow instructions in User Guide.

Failure

Setpoint Sensor

Failure

Setpoint sensor failure

detected

Setpoint sensor recovered

mA measurement

failed.

Change the printed circuit board module to a

new one and calibrate device. Follow instruc

tions in User Guide

Failure

Prestage Shortcircuit

Prestage shortcircuit error

Prestage shortcircuit recovered

Shortcircuit in the

prestage unit. Device

will go to Failsafe

position

Change Prestage unit and calibrate device.

Follow instructions in User Guide

Failure

Position Sensor Failure Position sensor failure

detected

Position sensor recovered

Position measurement

faulty.

Change the printed circuit board module

to a new one and calibrate device. Follow

instructions in User Guide

Failure

Prestage Open circuit

Prestage open circuit error

Prestage open circuit recovered

Prestage wire is cut or

connector is loose.

Change Prestage unit and calibrate device.

Follow instructions in User Guide

Failure

Position Transmitter

Not Connected

Position transmitter

is available. External

supply voltage is not

connected.

Connect external supply voltage or disable

status in DTM/EDD Status Configuration view.

Out of

Specification

13 DEVICE TYPE MANAGER (DTM)

OPER

ATION

Summary of Contents for NELES NDX 511 Series

























































































Search results

Summary of Contents for NELES NDX 511 Series

Reviews:

Related manuals for NELES NDX 511 Series

Brands by name

Popular brands

Metso NELES NDX 511 Series, Installation Maintenance And Operating Instructions

Search results

Summary of Contents for NELES NDX 511 Series

Reviews:

Related manuals for NELES NDX 511 Series

Brands by name

Popular brands