Metso NELES NDX 511 Series Installation Maintenance And Operating Instructions Download Page 19

Page: 19 / 88

GENER

INFO

SPECS

MOUNTING

T UP

OPER

ATION

AINTENANCE

DIMENSIONS

ORDER

LOGISTICS

NDX VALVE CONTROLLER

7.1

Installation to Neles Globe

NOTE

The enclosure of NDX meets the IP66 pro

tection class according to EN 60529. Cable

entry needs to be plugged according to IP66

and it is not allowed to mount NDX in a po

sition where the cable entry is pointing up

wards. Based on good mounting practice, the

recommended mounting position is electrical

connections placed downwards. This recom

mendation is shown in our mounting position

coding for control valves.

If these requirements are not fulfilled, and the

cable gland is leaking and the leakage is dam

aging NDX, our warranty is not valid.

MODEL VD25

MODEL VD29

MODEL VD37

MODEL VD48 AND 55

Fig. 13

7.1.1

Installation to Neles Globe (VD29)

1. Mount the magnet holder with magnet to the

actuator coupler, tighten the fixing screw.

Fig. 14

2. Mount the bracket to the actuator, leaving the screws

loose.

Fig. 15

5 mm

6 mm

13 mm or 21/22 mm

Depends on

actuator size

NOTE

Similar mounting steps apply also with other

Neles Globe actuator sizes.

NOTE

The bracket can be rotated 180° or flipped

front/backside. If the bracket is flipped, the

magnet needs to be flipped correspondingly.

If needed, check the magnet installation toler

ances from the picture in section 7.3 “Installa

tion to any linear actuator”

3. Attach the magnet alignment tool to the magnet.

Adjust the position of the bracket so that the

magnet slides smoothly in the magnet alignment

tool groove and tighten the magnet alignment tool

fixing bolts.

LINEAR MOUNTING

MOUNTING

Summary of Contents for NELES NDX 511 Series

























































































Search results

Summary of Contents for NELES NDX 511 Series

Reviews:

Related manuals for NELES NDX 511 Series

Brands by name

Popular brands

Metso NELES NDX 511 Series, Installation Maintenance And Operating Instructions

Search results

Summary of Contents for NELES NDX 511 Series

Reviews:

Related manuals for NELES NDX 511 Series

Brands by name

Popular brands