Metso NELES NDX 511 Series Installation Maintenance And Operating Instructions Download Page 41

Page: 41 / 88

GENER

INFO

SPECS

MOUNTING

T UP

OPER

ATION

AINTENANCE

DIMENSIONS

ORDER

LOGISTICS

NDX VALVE CONTROLLER

12.6

Exceptions

If position measurement goes out of range or fails, position

indicator shows on the LUI.

12.7

Remote actions

When calibration or offline test is started remotely (i.e.

from DTM), there is a warning on the LUI before the valve

starts to move.

12.8

Menu

Press Enter (o) to open menu.

•

Guided startup

•

Calibration

•

Parameters

•

Linearization

•

Manual control

•

User Guide

•

About

POS > 999 % or

sensor broken

12 LOCAL USER INTERFACE (LUI)

T UP

Summary of Contents for NELES NDX 511 Series

























































































Search results

Summary of Contents for NELES NDX 511 Series

Reviews:

Related manuals for NELES NDX 511 Series

Brands by name

Popular brands

Metso NELES NDX 511 Series, Installation Maintenance And Operating Instructions

Search results

Summary of Contents for NELES NDX 511 Series

Reviews:

Related manuals for NELES NDX 511 Series

Brands by name

Popular brands