Metso NELES NDX 511 Series Installation Maintenance And Operating Instructions Download Page 52

Page: 52 / 88

NDX VALVE CONTROLLER

13.3

User Interface Information

Figure below shows the DTM user interface. The user inter

face elements indicated by numbers are explained in more

detail below.

Fig. 51

1. Refresh button reloads the active view from the

device. This button can be used to cancel any modi

fication made to the local parameters.

2. OK button sends all modifications to the device and

closes the window.

3. Cancel button cancels all the local changes and

closes the window.

4. Apply button sends all local changes to the device.

5. Connected status shows, if connection to the device

is established, or if the DTM is in disconnected

(offline) mode.

6. Green arrow icon is displayed, when the DTM is

sending or reading parameters from the device.

7. Parameter set state. Device parameters are stored to

the device and also in the local database. This icon

shows, if the information shown in the DTM is updated

with the device, only saved to the local database.

8. Pencil icon is shown, when there are local modifica

tions to the device parameters, which are not saved

to the device.

9. Device variables are available in all views when device

connected online. Parameters shown are: Valve Posi

tion (POS), Target Position (TPOS), Setpoint (SETP),

Supply Pressure (S), Actuator Pressure I and II.

13 DEVICE TYPE MANAGER (DTM)

Summary of Contents for NELES NDX 511 Series

























































































Search results

Summary of Contents for NELES NDX 511 Series

Reviews:

Related manuals for NELES NDX 511 Series

Brands by name

Popular brands

Metso NELES NDX 511 Series, Installation Maintenance And Operating Instructions

Search results

Summary of Contents for NELES NDX 511 Series

Reviews:

Related manuals for NELES NDX 511 Series

Brands by name

Popular brands