Mercury 115 Pro XS FourStroke Operation Maintenance Warranty Installation Manual Download Page 9

Page: 9 / 159

Maintenance

Outboard Care.................................................................................................. 73

EPA Emissions Regulations............................................................................. 73

Inspection and Maintenance Schedule............................................................. 74

Flushing the Cooling System ........................................................................... 77

Top Cowl Removal and Installation.................................................................. 77

Cleaning Care for Top Cowl............................................................................. 78

Flywheel Cover Removal and Installation.........................................................78

Side Panel Removal and Installation................................................................ 79

OIl Injection System.......................................................................................... 80

Fuel System...................................................................................................... 83

Steering Link Rod Fasteners............................................................................ 85

Fuse Replacement............................................................................................86

Corrosion Control Anode.................................................................................. 87

Battery Inspection ............................................................................................ 88

Battery Information (All Batteries Including DTS)............................................. 88

Propellers..........................................................................................................89

Spark Plug Inspection and Replacement..........................................................92

Compressor Air Intake Filter............................................................................. 94

Alternator Belt Inspection..................................................................................95

Lubrication Points............................................................................................. 95

Lubrication Points............................................................................................. 97

Checking Power Trim Fluid...............................................................................99

Gearcase Lubrication......................................................................................100

Storage

Storage Preparation........................................................................................102

Fuel System.................................................................................................... 102

Protecting Internal Engine Components......................................................... 104

Protecting External Outboard Components.................................................... 104

Gearcase........................................................................................................ 104

Jet Drive..........................................................................................................104

Positioning Outboard for Storage................................................................... 104

Battery Storage............................................................................................... 105

eng

vii

Summary of Contents for 115 Pro XS FourStroke
































































































































































Search results

Summary of Contents for 115 Pro XS FourStroke

Reviews:

Mercury 115 Pro XS FourStroke, Operation Maintenance Warranty Installation Manual, Page: 9 / 159

Search results

Summary of Contents for 115 Pro XS FourStroke

Reviews: