manualshive.com logo in svg

Mercury 115 Pro XS FourStroke, Operation Maintenance Warranty Installation Manual, Page: 50 / 159

Share
Download
Mercury 115 Pro XS FourStroke Operation Maintenance Warranty Installation Manual Download Page 50

Models

75

90

115/115 Pro

XS

125

Sound at

drivers ear

(ICOMIA 39‑94)

dBA

82.0

*Battery manufacturers may rate and test their batteries to different standards.

MCA, CCA, Ah, and reserve capacity (RC) are the ratings recognized by

Mercury Marine. Manufacturers that use standards different than these, such

as equivalent MCA, do not meet Mercury Marine battery requirements.

80 Jet OptiMax Specifications

Models

80

Horsepower

80

Kilowatts

58.8

Full throttle RPM range

5000–5750 RPM

Idle speed in forward

gear

625–675 RPM

Number of cylinders

3

Piston displacement

1523.5 cc (92.9 in³)

Cylinder bore

92.11 mm (3.63 in.)

Piston stroke

76.2 mm (3.0 in.)

Recommended spark

plug

IZFR5J

Spark plug gap

0.80 mm (0.030 in.)

Recommended gasoline

Refer to 

Fuel and Oil

Recommended oil

Refer to 

Fuel and Oil

Oil tank capacity

4.72 liters (5 US qt)

Battery rating*

1000 marine cranking amps (MCA) or 800 cold

cranking amps (CCA)

Charging system output

60 A

Emission control system

Electronic engine control (EC)

*Battery manufacturers may rate and test their batteries to different standards.

MCA, CCA, Ah, and reserve capacity (RC) are the ratings recognized by

Mercury Marine. Manufacturers that use standards different than these, such

as equivalent MCA, do not meet Mercury Marine battery requirements.

GENERAL INFORMATION

  

40

eng

Summary of Contents for 115 Pro XS FourStroke
































































































































































Reviews:

No comments