manualshive.com logo in svg

Mercury 115 Pro XS FourStroke, Operation Maintenance Warranty Installation Manual, Page: 79 / 159

Share
Download
Mercury 115 Pro XS FourStroke Operation Maintenance Warranty Installation Manual Download Page 79

It is possible for debris to lodge between the impeller and jet housing wall,

especially after the engine has been stopped. This will lock the driveshaft and

will prevent the engine from being able to crank over for starting. Following are

steps for dislodging the impeller.

1. Position the lanyard stop switch to the "OFF" position.
2. Remove the spark plug leads to prevent the engine from accidentally

starting.

3. Remove the flywheel or rewind cover and rotate the engine flywheel

counterclockwise.

If this does not dislodge the impeller, it will be necessary to remove the six

screws and water intake housing.

STARTING THE ENGINE

Before starting, read the prestarting check list, special operating instructions,

and engine break‑in procedure in the 

Operation

 section.

NOTE: When the engine is being run within the RPM range of 3500–4200

RPM, there may be a slight RPM instability. This is caused by the light engine

load conditions normally seen with jet lower units. This condition will not cause

any adverse affects on the engine.

NOTICE

Without  sufficient  cooling  water,  the  engine,  the  water  pump,  and  other

components will overheat and suffer damage. Provide a sufficient supply of

water to the water inlets during operation.

1. Ensure that the driveshaft bearing on the jet drive is lubricated. Refer to

Maintenance 

‑

 Lubrication Points

.

28664

2. Open the fuel tank vent screw, located in the filler cap, on manual venting

type fuel tanks.

19748

OPERATION

eng

69

  

Summary of Contents for 115 Pro XS FourStroke
































































































































































Reviews:

No comments