manualshive.com logo in svg

Mercury 115 Pro XS FourStroke, Operation Maintenance Warranty Installation Manual, Page: 106 / 159

Share
Download
Mercury 115 Pro XS FourStroke Operation Maintenance Warranty Installation Manual Download Page 106

• Propeller shaft ‑ Refer to 

Propeller Replacement

 for removal and

installation of the propeller. Coat the entire propeller shaft with

lubricant to prevent the propeller hub from corroding and seizing to the

shaft.

26902

2. Lubricate the following with 2‑4‑C with PTFE.

Tube Ref

No.

Description

Where Used

Part No.

95

2-4-C with PTFE

Swivel bracket, tilt support lever, tilt

tube, steering cable grease fitting

92-802859A 1

• Swivel bracket ‑ Lubricate through fitting.
• Tilt support lever ‑ Lubricate through fitting.

a -

Swivel bracket

b -

Tilt support lever

• Tilt tube ‑ Lubricate through fitting.

29478

• Steering cable grease fitting (if equipped) ‑ Rotate steering wheel to

fully retract the steering cable end into the outboard tilt tube. Lubricate

through fitting.

a

b

27873

MAINTENANCE

  

96

eng

Summary of Contents for 115 Pro XS FourStroke
































































































































































Reviews:

No comments