manualshive.com logo in svg

Mercury 115 Pro XS FourStroke, Operation Maintenance Warranty Installation Manual, Page: 131 / 159

Share
Download
Mercury 115 Pro XS FourStroke Operation Maintenance Warranty Installation Manual Download Page 131

4. Turn the key switch to the "ON" position again for three seconds.
5. Continue this procedure until the fuel line primer bulb stays firm.

Installation Specifications

a -

Minimum transom opening

b -

Engine centerline for dual engine ‑ 66.0 cm (26 in.)

Minimum Transom Opening
   Single engine

84.2 cm (33 in.)

   Dual engine

149.9 cm (59 in.)

Lifting the Outboard

!

 WARNING

Improperly supporting an engine during lifting can result in the engine falling,

causing serious injury or death. Before lifting the engine, verify that the lifting

ring  is  threaded  into  the  flywheel  for  a  minimum  of  five  turns  and  that  the

hoist has the correct lifting capacity for the engine weight.

To lift the outboard:

1. Remove the cowl from the outboard.

18552

a

a

b

OUTBOARD INSTALLATION

eng

121

  

Summary of Contents for 115 Pro XS FourStroke
































































































































































Reviews:

No comments