manualshive.com logo in svg

Mercury 115 Pro XS FourStroke, Operation Maintenance Warranty Installation Manual, Page: 101 / 159

Share
Download
Mercury 115 Pro XS FourStroke Operation Maintenance Warranty Installation Manual Download Page 101

4. Place a block of wood between the gearcase and propeller and remove

the propeller nut.

26901

5. Pull the propeller straight off the shaft. If the propeller is seized to the

shaft and cannot be removed, have the propeller removed by an

authorized dealer.

INSTALLATION

IMPORTANT: To prevent the propeller hub from corroding and seizing to the

propeller shaft (especially in saltwater), always apply a coat of the

recommended lubricant to the entire propeller shaft at the recommended

maintenance intervals and also each time the propeller is removed.

1. Coat the propeller shaft with Extreme Grease or 2‑4‑C with PTFE.

26902

Tube Ref

No.

Description

Where Used

Part No.

Extreme Grease

Propeller shaft

8M0071842

95

2-4-C with PTFE

Propeller shaft

92-802859A 1

NOTE: The Flo‑Torq lll propeller drive hubs are designed to have a small

amount of free play when installed. This free play allows the propeller to slide

back and forth on the rear thrust hub (up to 3.17 mm [1/8 in.]) and rotate up to

10 degrees.

MAINTENANCE

eng

91

  

Summary of Contents for 115 Pro XS FourStroke
































































































































































Reviews:

No comments