Mercury 115 Pro XS FourStroke Operation Maintenance Warranty Installation Manual Download Page 94

Page: 94 / 159

Fuel Filter Removal/Installation Tool

91‑896661

24896

Aids in the removal and installation of the

fuel filter cap assembly.

Installation

1. Lubricate the O‑ring seals with oil.
2. Install the fuel filter and tighten securely.
3. Squeeze the primer bulb until firm and inspect for fuel leakage at the filter.

DRAINING WATER FROM THE FUEL FILTER CHAMBER
NOTE: If a sufficient amount of water has accumulated in the fuel filter

chamber, the warning system will turn on. Draining the water from the fuel filter

chamber is required.

1. Pull the drain hose off the right side fitting. Hold the open end of the hose

over a container.

2. Use a 1/8 in. hex wrench and loosen the drain screw and drain the fuel

filter chamber.

a -

Drain hose

b -

Right side fitting

c -

Drain screw

3. Tighten the drain screw and attach the hose.

23743

MAINTENANCE

eng

Summary of Contents for 115 Pro XS FourStroke
































































































































































Search results

Summary of Contents for 115 Pro XS FourStroke

Reviews:

Mercury 115 Pro XS FourStroke, Operation Maintenance Warranty Installation Manual, Page: 94 / 159

Search results

Summary of Contents for 115 Pro XS FourStroke

Reviews: