Mercury 115 Pro XS FourStroke Operation Maintenance Warranty Installation Manual Download Page 107

Page: 107 / 159

WARNING

Incorrect cable lubrication can cause hydraulic lock, leading to serious

injury or death from loss of boat control. Completely retract the end of the

steering cable before applying lubricant.

a -

Fitting

b -

Steering cable end

3. Lubricate the following with lightweight oil.

• Steering link rod pivot points ‑ Lubricate pivot points.

29480

Lubrication Points

1. Lubricate the following with Quicksilver or Mercury Precision 2‑4‑C with

PTFE.

Tube Ref

No.

Description

Where Used

Part No.

2-4-C with PTFE

Driveshaft bearing

92-802859A 1

IMPORTANT: It is important not to use a general all‑purpose grease for this

bearing. The lubricant recommended is a water‑resistant grease of the proper

consistency for this application. If a substitute is used, be sure that it is

water‑resistant.

• Driveshaft bearing

i. Pull the vent hose off of the grease fitting.
ii. Pump in grease through the grease fitting until excess grease

starts to exit the vent hose.

29479

MAINTENANCE

eng

Summary of Contents for 115 Pro XS FourStroke
































































































































































Search results

Summary of Contents for 115 Pro XS FourStroke

Reviews:

Mercury 115 Pro XS FourStroke, Operation Maintenance Warranty Installation Manual, Page: 107 / 159

Search results

Summary of Contents for 115 Pro XS FourStroke

Reviews: