manualshive.com logo in svg

Mercury 115 Pro XS FourStroke, Operation Maintenance Warranty Installation Manual, Page: 99 / 159

Share
Download
Mercury 115 Pro XS FourStroke Operation Maintenance Warranty Installation Manual Download Page 99

A decal advising against using deep cycle batteries and wing nuts should be

placed on or near the battery box for future service reference. One 5/16 in. and

one 3/8 in. hex nut is supplied per battery for wing nut replacement. Metric hex

nuts are not supplied.

54395

Place decal on or near battery box for future 

service reference.  Included with the engine 

rigging components are 5/16" and 3/8” hex 

nuts to be used for battery terminal wing nut 

replacement.  Metric hex nuts must be obtained 

locally.

8M0085862

Refer to the outboard owner’s manual for 

battery requirements.

Battery cable size and length is critical.  

Refer to engine installation manual for 

size 

requirements. 

NOTICE

IMPORTANT:  

DO NOT USE DEEP CYCLE BATTERIES!

13.5Nm (120 lb-in.) 

DO NOT

USE

WINGNUTS

Propellers

REMOVAL

IMPORTANT: Propellers used on this product require the Mercury Marine

Flo‑Torq III type hub or equivalent.

!

 WARNING

Rotating propellers can cause serious injury or death. Never operate the boat

out  of  the  water  with  a  propeller  installed.  Before  installing  or  removing  a

propeller, place the drive unit in neutral and engage the lanyard stop switch

to  prevent  the  engine  from  starting.  Place  a  block  of  wood  between  the

propeller blade and the anti‑ventilation plate.

MAINTENANCE

eng

89

  

Summary of Contents for 115 Pro XS FourStroke
































































































































































Reviews:

No comments