manualshive.com logo in svg

Mercury 115 Pro XS FourStroke, Operation Maintenance Warranty Installation Manual, Page: 111 / 159

Share
Download
Mercury 115 Pro XS FourStroke Operation Maintenance Warranty Installation Manual Download Page 111

GEARCASE LUBRICANT RECOMMENDATION

Mercury or Quicksilver Premium or High Performance Gear Lubricant.

CHECKING LUBRICANT LEVEL AND FILLING GEARCASE

1. Place the outboard in a vertical operating position.
2. Remove the front vent plug and rear vent plug.
3. Remove the fill/drain plug. Place the lubricant tube into the fill/drain plug

hole and add lubricant until it appears at the front vent hole. At this time

install the front vent plug and sealing washer.

a -

Front vent plug

b -

Front vent hole

c -

Rear vent hole

d -

Rear vent plug

e -

Fill/drain plug

4. Continue adding the lubricant until it appears at the rear vent hole.
5. Stop adding the lubricant. Install the rear vent plug and sealing washer

before removing lubricant tube.

6. Remove the lubricant tube and install cleaned fill/drain plug and sealing

washer.

SUBMERGED OUTBOARD

A submerged outboard will require service within a few hours by an authorized

dealer once the outboard is recovered from the water. This immediate attention

by a servicing dealer is necessary once the engine is exposed to the

atmosphere to minimize internal corrosion damage to the engine.

27001

b

a

c

d

e

MAINTENANCE

eng

101

  

Summary of Contents for 115 Pro XS FourStroke
































































































































































Reviews:

No comments