manualshive.com logo in svg

Mercury 115 Pro XS FourStroke, Operation Maintenance Warranty Installation Manual, Page: 80 / 159

Share
Download
Mercury 115 Pro XS FourStroke Operation Maintenance Warranty Installation Manual Download Page 80

3. Position the fuel line primer bulb so the arrow on the side of the bulb is

pointing up. Squeeze the fuel line primer bulb several times until it feels

firm.

27348

4. Set the lanyard stop switch to "RUN" position. Refer to 

General

Information 

‑

 Lanyard Stop Switch

.

19791

5. Shift the outboard to neutral ("N") position.

N 

26838

6. For the initial start of a new engine, or for an engine that ran out of fuel or

was drained of fuel, the fuel system should be filled as follows:

a. Squeeze the fuel line primer bulb until it feels firm.
b. Turn the ignition key switch to the "ON" position for three seconds.

This operates the electric fuel pump.

c. Turn the ignition key switch back to the "OFF" position, and squeeze

the primer bulb again until it feels firm. Turn the ignition key switch to

the "ON" position again for three seconds. Continue this procedure

until the fuel line primer bulb stays firm.

OPERATION

  

70

eng

Summary of Contents for 115 Pro XS FourStroke
































































































































































Reviews:

No comments