manualshive.com logo in svg

Mercury 115 Pro XS FourStroke, Operation Maintenance Warranty Installation Manual, Page: 66 / 159

Share
Download
Mercury 115 Pro XS FourStroke Operation Maintenance Warranty Installation Manual Download Page 66

Turn out the manual tilt release valve three turns counterclockwise. This allows

manual tilting of the outboard. Tilt the outboard to the desired position and

tighten the manual tilt release valve.

22362

SHALLOW WATER OPERATION

When operating your boat in shallow water, you can tilt the outboard beyond

the maximum trim range to prevent hitting bottom.

1. Reduce the engine speed below 2000 RPM.
2. Tilt the outboard up. Make sure all the water intake holes stay submerged

at all times.

3. Operate the engine at slow speed only. If engine speed exceeds 2000

RPM, the outboard will automatically return down to the maximum trim

range.

AUXILIARY TILT SWITCH

The auxiliary tilt switch can be used to tilt the outboard up or down using the

power trim system.

a -

Auxiliary tilt switch

a

27779

FEATURES AND CONTROLS

  

56

eng

Summary of Contents for 115 Pro XS FourStroke
































































































































































Reviews:

No comments