Mercury 115 Pro XS FourStroke Operation Maintenance Warranty Installation Manual Download Page 95

Page: 95 / 159

IMPORTANT: Visually inspect for fuel leakage from the drain screw by

squeezing the primer bulb until firm, forcing fuel into the chamber.

Steering Link Rod Fasteners

IMPORTANT: The steering link rod that connects the steering cable to the

engine must be fastened using a special washer head bolt ("a" ‑ Part Number

10‑849838) and self‑locking nylon insert locknuts ("c" and "d" ‑ Part Number

11‑826709113). These locknuts must never be replaced with common nuts

(nonlocking) as they will work loose and vibrate off, freeing the link rod to

disengage.

WARNING

Improper fasteners or improper installation procedures can result in

loosening or disengagement of the steering link rod. This can cause a

sudden, unexpected loss of boat control, resulting in serious injury or death

due to occupants being thrown within or out of the boat. Always use required

components and follow instructions and torque procedures.

a -

Special washer head bolt (10‑849838)

b -

Flat washer (2)

c -

Nylon insert locknut (11‑826709113)

d -

Nylon insert locknut (11‑826709113)

Description

lb‑in.

lb‑ft

Special washer head bolt

–

Nylon insert locknut "d"

–

Nylon insert locknut "c"

Tighten until it seats, then back off 1/4

turn

27843

MAINTENANCE

eng

Summary of Contents for 115 Pro XS FourStroke
































































































































































Search results

Summary of Contents for 115 Pro XS FourStroke

Reviews:

Mercury 115 Pro XS FourStroke, Operation Maintenance Warranty Installation Manual, Page: 95 / 159

Search results

Summary of Contents for 115 Pro XS FourStroke

Reviews: