Mercury 115 Pro XS FourStroke Operation Maintenance Warranty Installation Manual Download Page 102

Page: 102 / 159

Flo

‑

Torq III drive hub propellers

‑ Install the forward thrust hub,

replaceable drive sleeve, propeller, thrust hub, propeller nut retainer, and

propeller nut onto the shaft.

a -

Propeller nut

b -

Propeller nut retainer

c -

Rear thrust hub

d -

Propeller

e -

Replaceable drive sleeve

f -

Forward thrust hub

3. Place a block of wood between the gearcase and propeller. Torque the

propeller nut to specification.

Description

lb‑in.

lb‑ft

Propeller nut

–

4. Secure the propeller nut by bending three of the tabs into the thrust hub

grooves.

26945

Spark Plug Inspection and Replacement

WARNING

Damaged spark plug boots may emit sparks that can ignite fuel vapors under

the engine cowl, resulting in serious injury or death from a fire or explosion.

To avoid damaging the spark plug boots, do not use any sharp object or

metal tool to remove the spark plug boots.

3223

MAINTENANCE

eng

Summary of Contents for 115 Pro XS FourStroke
































































































































































Search results

Summary of Contents for 115 Pro XS FourStroke

Reviews:

Mercury 115 Pro XS FourStroke, Operation Maintenance Warranty Installation Manual, Page: 102 / 159

Search results

Summary of Contents for 115 Pro XS FourStroke

Reviews: