manualshive.com logo in svg

Mercury 115 Pro XS FourStroke, Operation Maintenance Warranty Installation Manual, Page: 109 / 159

Share
Download
Mercury 115 Pro XS FourStroke Operation Maintenance Warranty Installation Manual Download Page 109

• Steering cable grease fitting (if equipped) ‑ Rotate steering wheel to

fully retract the steering cable end into the outboard tilt tube. Lubricate

through fitting.

!

 WARNING

Incorrect  cable  lubrication  can  cause  hydraulic  lock,  leading  to  serious

injury or death from loss of boat control. Completely retract the end of the

steering cable before applying lubricant.

a -

Fitting

b -

Steering cable end

3. Lubricate the following with lightweight oil.

• Steering link rod pivot points ‑ Lubricate pivot points.

29480

Checking Power Trim Fluid

1. Tilt the outboard to the full up position and engage the tilt support lever.

27877

2. Remove the fill cap and check the fluid level. The fluid level should be

even with the bottom of the fill hole. Add Quicksilver or Mercury Precision

Lubricants Power Trim and Steering Fluid. If not available, use automotive

automatic transmission fluid (ATF).

a

b

29479

MAINTENANCE

eng

99

  

Summary of Contents for 115 Pro XS FourStroke
































































































































































Reviews:

No comments