manualshive.com logo in svg

Mercury 115 Pro XS FourStroke, Operation Maintenance Warranty Installation Manual, Page: 114 / 159

Share
Download
Mercury 115 Pro XS FourStroke Operation Maintenance Warranty Installation Manual Download Page 114

Flushing Device

91‑44357Q 2

9192

Attaches to the water intakes; provides

a fresh water connection when flushing

the cooling system or operating the

engine.

Protecting Internal Engine Components

NOTE: Make sure the fuel system has been prepared for storage. Refer to 

Fuel

System

, preceding.

IMPORTANT: Refer to

 Spark Plug Inspection and Replacement f

or correct

procedure for removing spark plug leads.

1. Remove the spark plugs. Add approximately 30 ml (1 oz) of engine oil or

inject a five second spray of storage seal into each spark plug hole.

2. Rotate the flywheel manually several times to distribute the oil or storage

seal in the cylinders.

3. Install the spark plugs.

Protecting External Outboard Components

•

Lubricate all outboard components listed in 

Maintenance 

‑

 Inspection

and Maintenance Schedule

.

•

Touch up any paint nicks. See your dealer for touch‑up paint.

•

Spray Quicksilver or Mercury Precision Lubricants Corrosion Guard on

external metal surfaces (except corrosion control anodes).

Tube Ref

No.

Description

Where Used

Part No.

120

Corrosion Guard

External metal surfaces

92-802878 55

Gearcase

•

Drain and refill the gearcase lubricant (refer to

 Gearcase Lubrication

).

Jet Drive

•

Pump extra grease into the jet drive bearing to purge out moisture.

Positioning Outboard for Storage

Store outboard in an upright (vertical) position to allow water to drain out of the

outboard.

STORAGE

  

104

eng

Summary of Contents for 115 Pro XS FourStroke
































































































































































Reviews:

No comments