manualshive.com logo in svg

Mercury 115 Pro XS FourStroke, Operation Maintenance Warranty Installation Manual, Page: 90 / 159

Share
Download
Mercury 115 Pro XS FourStroke Operation Maintenance Warranty Installation Manual Download Page 90

INSTALLATION

Position the side panel onto the three mounting pins. Insert the tabs on the

flywheel cover into the upper slots and push the side panel onto the mounting

pins.

a -

Side panel

b -

Upper slots

c -

Mounting pins

OIl Injection System

OIL INJECTION FILTER

IMPORTANT: The oil injection in‑line filter must be replaced after the first 100

hours of operation. Afterwards, this filter must be replaced every 300 hours of

operation. After replacing the in‑line filter, the oil injection system must be

purged to remove air trapped in the system.

1. Cut the cable ties securing the in‑line oil filter.
2. Place an appropriate container or shop towels under the in‑line filter to

capture oil that will leak out of the hoses.

IMPORTANT: The arrow on the filter identifies the direction of the oil flow and

should point towards the oil pump.

3. Quickly remove the old filter and install a new filter.

c

a

b

23765

MAINTENANCE

  

80

eng

Summary of Contents for 115 Pro XS FourStroke
































































































































































Reviews:

No comments