MDT Technologies BE-BZS86.01 Technical Manual Download Page 32

Page: 32 / 164

Technical Manual

–

Central Operation Unit Smart

MDT technologies GmbH •

51766 Engelskirchen • Papiermühle 1

Phone: +49-2263-

880 • Fax: +49-2263-4588 • [email protected] • www.mdt.de

Colour of message text

Any colour

[red]

Setting the color for the
message text

Indicate a message via LEDs

▪

Yes

Setting whether the LEDs
should flash when a message is
active

Colour of LEDs

Any colour

[white]

Only appears if "Indicate
message via LEDs" is active

Table 19: Settings - Messages and Alarms

The message behaviour depends on the parameter "Standby display during day/night". The different
behaviours are shown below:

Standby display

Incoming message in standby

No Standby

▪

No message is displayed, but saved

Standby in upper
third, status LEDs
active

▪

Message is displayed on upper button pair and the upper LEDs
change between parameterized color and black at 600ms pulse

▪

At the same time, the parameterized color is set to double
brightness in order to increase the signal effect

▪

The message is only acknowledged by pressing to one of the
upper buttons.

▪

A keystroke on the middle and lower buttons performs the
displayed switching functions

Full screen standby,
LEDs active

▪

Message is displayed in the middle of the screen and all LEDs
change between parameterized color and black

▪

At the same time, the parameterized color is set to double
brightness in order to increase the signal effect.

▪

The message is acknowledged by pressing to any key

Display and LEDs off

▪

No message is displayed during standby but saved.

▪

The message with the highest priority is indicated by the
keystroke after standby

▪

The displayed messages are acknowledged by means of further
key strokes

▪

Message is displayed in the middle of the screen and all LEDs
change between parameterized color and black

▪

At the same time, the parameterized color is set to double
brightness in order to increase the signal effect.

Display off and LEDs
on

▪

Message is displayed in the middle of the screen and all LEDs
change between parameterized color and black

▪

At the same time, the parameterized color is set to double
brightness in order to increase the signal effect.

▪

After the "timeout for standby", the LEDs will stop flashing and
the message dispappears.

▪

If any button is pressed after the LEDs have stopped flashing, the
message with the highest priority is displayed again. Further
keystrokes acknowledge the messages

Table 20: Behaviour on receipt of a message in standby

Summary of Contents for BE-BZS86.01





































































































































































Search results

Summary of Contents for BE-BZS86.01

Reviews:

Related manuals for BE-BZS86.01

Brands by name

Popular brands

MDT Technologies BE-BZS86.01, Technical Manual

Search results

Summary of Contents for BE-BZS86.01

Reviews:

Related manuals for BE-BZS86.01

Brands by name

Popular brands