LV switch IPPBX3000 User Manual Download

Page: 37 / 195

LvSwitch IPPBX 3000 Manual

Equipment Summary

Summary

The equipment Summary includes System Status and Info Statistics.

4.1 System Status

The System Status includes Device overview and the Interface status.

4.1.1 Device Overview

Select “System Status > Device” to enter the Device page as shown in Figure 4-1.

Figure4- 1 Device Overview

The Device overview shows the software version, hardware version, MAC address, Device ID, Uplink mode,
Productclass,CPU usage, Memory Usage. Click < Refresh> to display the current CPU usage and memory
usage.

4.1.2 Interface Status

Select “System Status > Interface” to enter the Interface page as shown in Figure 4-2.

Summary of Contents for IPPBX3000




































































































































































































Search results

Summary of Contents for IPPBX3000

Reviews:

Related manuals for IPPBX3000

Brands by name

Popular brands

LV switch IPPBX3000, User Manual

Search results

Summary of Contents for IPPBX3000

Reviews:

Related manuals for IPPBX3000

Brands by name

Popular brands