manualshive.com logo in svg

LV switch IPPBX3000, User Manual

Share
Download
LV switch IPPBX3000 User Manual Download Page 98

LvSwitch IPPBX 3000 Manual

96

Figure 6-30 Advanced setting

Table 6-11 Advanced setting of SS7 trunk

Note:

Source code type must be set. 24-bit code type is used domestically and 14-bit code type is used
internationally.

Modify/delete SS7 Trunk

In the "SS7 relay" list, click the SS7 relay you want to modify, and click the

button to modify the setting

information of the specified SS7 relay in the pop-up interface.

Select an SS7 relay in the "SS7 relay" list that you want to delete, and click

the button to delete the specified

SS7 relay.

6.3.2 SIP Regitry

SIP Registry used when SIP trunk type is UNI mode.

Click “Voice Config>>Trunks Config>>SIP Registry” to open the page as shown in the following figure.

ITEMS

Description

Relay fault determination

When the relay fault duration reaches the set value, the fault
message will be sent to the corresponding incoming relay. After
the recovery of the relay fault, when the normal operation
reaches the value, the corresponding relay service will be
informed to start.Default 60 seconds, value range: 1 to 300
seconds.

Summary of Contents for IPPBX3000




































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands