LV switch IPPBX3000 User Manual Download

Page: 123 / 195

LvSwitch IPPBX 3000 Manual

121

Figure 6-65 Music Ring

Add a CRBT

Click <Add> to open the page as shown in the following figure.

Figure 6-66 Add Music ringtone Back Tone

Click <Browser> button to select local music files, and then click the <Upload> button to upload the music
to system.

Play CRBT

Click <

> button to play CRBT.

Search CRBT

Click <

> button to open the page as shown in the following figure.

Figure 6-67 Search CRBT

Users can search CRBT by name.

Note:

(1) Users can upload or record personalized color ringtones in the self-service system.

(2) Upload audio files in 8kHz, 16bit, mono format of wav, alaw, ulaw and GSM file.

Summary of Contents for IPPBX3000




































































































































































































Search results

Summary of Contents for IPPBX3000

Reviews:

Related manuals for IPPBX3000

Brands by name

Popular brands

LV switch IPPBX3000, User Manual

Search results

Summary of Contents for IPPBX3000

Reviews:

Related manuals for IPPBX3000

Brands by name

Popular brands