LV switch IPPBX3000 User Manual Download

Page: 101 / 195

LvSwitch IPPBX 3000 Manual

Batch Import SIP Account

Click <import> botton and select Excel file to import.

Figure 6-34 Batch Import SIP Account

Search SIP Registry

Click <Search> button to open the page as shown in the following figure.

Figure 6-35 Search SIP Registry

6.3.3 Inbound Call Routing

By setting inbound call routing, incoming calls from analog trunk can be transferred to internal extensions,
IVR or agents. Users can set different inbound call routing in different time period.

Select " Voice Config>>Trunks Config>>Inbound Call " to open the page as shown in the following figure.

Figure 6-36 Inbound Call Routing

Add inboud call routing

Click <Add> button to open the page as shown in the following figure.

Summary of Contents for IPPBX3000




































































































































































































Search results

Summary of Contents for IPPBX3000

Reviews:

Related manuals for IPPBX3000

Brands by name

Popular brands

LV switch IPPBX3000, User Manual

Search results

Summary of Contents for IPPBX3000

Reviews:

Related manuals for IPPBX3000

Brands by name

Popular brands