LV switch IPPBX3000 User Manual Download

Page: 100 / 195

LvSwitch IPPBX 3000 Manual

Item

Description

Registry or not

Select “Yes”, this account will be registered; select “No”, this account will not be
registered

Registry Time

Default registry time is 1,800s

Click <Advanced> button to open the page as shown in the following figure.

Figure 6-33 SIP Add a New SIP Registry - Advanced

Interface items are described as follows:

Table 6- 12

Add a

New SIP Registry - Advanced

Item

Description

Max Calls

Default value is “1”

Send Flash

Type and select “Yes” if you want to send Flash

DTMF

Option: RFC 2833, info and inband

Fax Mode

Option: T.38, T.30

Enable RFC3581

Yes or No, default Yes

Enable Routing Mode

Yes or No, default Yes

Register/Logout SIP account

Select SIP account and click <Register> button to register SIP account.

Select SIP account and click <Logout> button to register SIP account.

Edit SIP account

Select SIP account and click <Edit> button to edit SIP account.

Delete SIP account

Select SIP account and click <Delete> button to delete SIP account.

Summary of Contents for IPPBX3000




































































































































































































Search results

Summary of Contents for IPPBX3000

Reviews:

Related manuals for IPPBX3000

Brands by name

Popular brands

LV switch IPPBX3000, User Manual

Search results

Summary of Contents for IPPBX3000

Reviews:

Related manuals for IPPBX3000

Brands by name

Popular brands