LG ARWN038GA2 Service Manual Download Page 9

Page: 9 / 81

- 9 -

LGE Internal Use Only

Safety Precautions

Turn on the power at least 6 hours before
starting operation.

• Starting operation immediately after turning on

the main power switch can result in severe
damage to internal parts. Keep the power switch
turned on during the operational season.

Do not touch any of the refrigerant piping
during and after operation.

• It can cause a burn or frostbite.

Do not operate the air conditioner with the
panels or guards removed.

• Rotating, hot, or high-voltage parts can cause

injuries.

Do not directly turn off the main power
switch after stopping operation.

• Wait at least 5minutes before turning off the

main power switch. Otherwise it may result in
water leakage or other problems.

Auto-addressing should be done in condition of
connecting the power of all indoor and outdoour
units. Auto-addressing should also be done in
case of changing the indoor unit PCB.

Use a firm stool or ladder when cleaning or
maintaining the air conditioner.

• Be careful and avoid personal injury.

Do not insert hands or other objects through the air inlet or outlet while the air conditioner is
plugged in.

• There are sharp and moving parts that could cause personal injury.

Summary of Contents for ARWN038GA2














































































Search results

Summary of Contents for ARWN038GA2

Reviews:

LG ARWN038GA2, Service Manual, Page: 9 / 81

Search results

Summary of Contents for ARWN038GA2

Reviews: