LG ARWN038GA2 Service Manual Download Page 38

Page: 38 / 81

- 38 -

LGE Internal Use Only

Checking Method for Key Components

EEV

ø5

Red

White

Yellow

Orange

Blue

ø4

DC 12V

Driving%

circuit

ø3

ø2

ø1

ø4

ø3

ø2

ø1

• Pulse signal output value and valve operation

• Output pulse sequence

- In valve close state: 1

→

- In valve open state: 11

→

* 1. If EEV open angle does not change, all of output phase will be OFF

2. If output phase is different or continuously in the ON state, motor will not operate smoothly and start

vibrating.

• EEV valve operation

ø1

OFF

ø2

OFF

ø3

OFF

ø4

OFF

Output (ø) No.

Output state

Valve%
open%
Angle

pulse

open

Full open%
1350 pulses

- At power ON, open angle signal of 1400 pulses out-

put and valve position is set to

ⓐ

If valve operates smoothly, no noise and vibration
occurs and if valve is closed. noise occurs.

- Noise from EEV can be confirmed by touching the

EEV surface with a screw driver and listening the
EEV noise.

- If liquid refrigerant is in EEV, the noise is lower.

2.2 Electronic Expansion Valve

Summary of Contents for ARWN038GA2














































































Search results

Summary of Contents for ARWN038GA2

Reviews:

LG ARWN038GA2, Service Manual, Page: 38 / 81

Search results

Summary of Contents for ARWN038GA2

Reviews: