manualshive.com logo in svg

LG ARWN038GA2, Service Manual, Page: 65 / 81

Share
Download
LG ARWN038GA2 Service Manual Download Page 65

Troubleshooting Guide

- 65 -

Copyright ©2013 LG Electronics. Inc. All right reserved.
Only for training and service purposes

LGE Internal Use Only

■

Error diagnosis and countermeasure flow chart

1. Defective low pressure sensor
2. Defective outside/indoor unit fan
3. Refrigerant shortage/leakage
4. Deformation because of damage of refrigerant pipe
5. Defective indoor / outside unit EEV
6. Covering / clogging 

(outside unit covering during the cooling mode/

indoor unit filter clogging during heating mode)

7. SVC valve clogging
8. Defective outside unit PCB
9. Defective indoor unit pipe sensor

Error

No.

Error Type

Error Point

Main Reasons

Error happens
because of 3 times
successive compres-
sor off due to exces-
sive drop of low pres-
sure by the low pres-
sure sensor

Excessive drop of
discharge  pressure
of compressor

35*

Is service valve

opened?

Open service valve

Are transmission cable/

piping normal?

Yes

No

Is amount of refrigerant

normal?

[refer refrigerant part]

Yes

No

Is fan normal?

(in heating outside fan,

in cooling indoor fan)

Yes

Adjust the amount of 
refrigerant (Additive charge)

check transmission/
piping correction.

Check and replace related parts
(error 105~108 reference)

Is strainer Ok?*

No

Replace the strainer

No

Replace the pressure sensor

Yes

Yes

Check indoor / outside unit LEV
Check Indoor unit PCB
Check indoor / outside unit 
installation conditions

Yes

Are the values of manifold 

and low pressure sensor same?

( Is the low pressure value

actually low?)

No

Is there pipe crack or trace 

of refrigerant leakage?

Weld / reconnect the cracked 
portion and recharge refrigerant

No

Yes

* If the temperature difference between inlet and outlet of strainer
   is so large that frost or ice formation can be seen or confirmed 
   then clogging of strainer should be checked
   (Notice: it is not full ice forming of strainer, in case that there is 
    not at inlet portion but at outlet portion)

Summary of Contents for ARWN038GA2


















































































Reviews:

No comments